English
Español
  • Search
    • +34 902930427

    0.00 €

    PCI Centrals and Modules

    Products 406
    UTC™ KILSEN® LED Card - 24 Zones [KFP-A-ZI-24-S]
    UTC™ KILSEN® LED Card - 24 Zones
    Ref.: KFP-A-ZI-24-S
    This zone indicator LED panel will provide you with LED indication with ample space for text for all 24 zones. It can be connected directly to the easily removable front door of the control panel or repeater. For this, it does not require additional cables. The panel will provide you with 1 red alarm LED and 1 yellow trouble LED per zone.
    V.A.T. included
    Consult
    UTC™ KILSEN® LED Board - 20 Zones [KFP-A-ZI-20]
    UTC™ KILSEN® LED Board - 20 Zones
    Ref.: KFP-A-ZI-20
    This zone indicator LED panel will provide you with LED indication with ample space for text for all 20 zones. It can be connected directly to the easily removable front door of the control panel or repeater. For this, it does not require additional cables. The panel will provide you with 1 red alarm LED and 1 yellow trouble LED per zone.
    V.A.T. included
    Consult
    UTC™ KILSEN® RS232 Kit [ 2010-2-232-KIT]
    UTC™ KILSEN® RS232 Kit
    Ref.: 2010-2-232-KIT
    RS232 communication kit for analogicals panels.
    V.A.T. included
    Consult
    UTC™ KILSEN® Transmitter Communicator Digital Alarm [ 2010-2-DACT]
    UTC™ KILSEN® Transmitter Communicator Digital Alarm
    Ref.: 2010-2-DACT
    Digital alarm transmitter for KFP-AF panels through PSTN switched phone line. Optional GPRS communication through ATS7310 module (See intrusion device).
    V.A.T. included
    Consult
    UTC™ KILSEN® Card for RS485 Communication Network [ 2010-2-NB]
    UTC™ KILSEN® Card for RS485 Communication Network
    Ref.: 2010-2-NB
    Network card for 2010 serie panels that permit create a network of analogicals and conventionals panels (Clase A/B), with a maximum of 32 nodes /32 loops/ 64 zones.
    V.A.T. included
    Consult
    UTC™ KILSEN® Expandable Link Card - 2 Loops [KFP-A-LB]
    UTC™ KILSEN® Expandable Link Card - 2 Loops
    Ref.: KFP-A-LB
    Expandable card with two loops for KFP-A panels. Provides 128 additionals zones with 4 programmable outputs. Cards can be connected directly to panel chasis without requirement of additional wire.
    V.A.T. included
    Consult
    Surface Mount Back Box for UTC™ GST® Interface Modules [B-9310]
    Surface Mount Back Box for UTC™ GST® Interface Modules
    Ref.: B-9310
    Back box for I-M9300. I-M9300 Addressable Input Module can receive normally open contact signal from field devices and transmit the action signal to fire alarm control panel (FACP). In case the input loop is broken, the module is able to transmit the fault information to the FACP, and the FACP will then display the address of the module.
    V.A.T. included
    Consult
    UTC™ GST® Intelligent Addr. Dual Input/Output Module (24VDC) [I-9303]
    UTC™ GST® Intelligent Addr. Dual Input/Output Module (24VDC)
    Ref.: I-9303
    Intelligent addressable input/output module. With 2 indipendant volt free relay with N/O and N/C change over contacts that can be driven via the fire alarm loop. Commonly used for overriding equipment such as AHU’s, smoke extracts, lift returns, auto dialer, BMS, etc. The input can be linked through a volt free contact switch output of ancillary equipment reporting to the fire alarm controller. According to the pre-inputted cause and effects interface programming, the alarm controller sends out a start command to the equipment required to start. After receiving the command, the module activates its relay to change state. Once the equipment under control has operated a confirmation signal can be sent back to the fire alarm controller. Electronic addressing can be done through Handheld Programming tool (P-9910B), purchased separately.
    V.A.T. included
    Consult
    UTC™ GST® Intelligent Addr. Single Input Module, Loop Powered [I-9300]
    UTC™ GST® Intelligent Addr. Single Input Module, Loop Powered
    Ref.: I-9300
    I-9300 Addressable Input Module is designed to receive normally open or normally closed switch signal from fire devices with coincidence functions, and transmits these messages to fire alarm control panel (FACP) with coincidence detection function. When a device of this kind is activated, the module can send the output signal through signal loop to FACP to alarm or activate relative devices.
    V.A.T. included
    Consult
    UTC™ GST® Loop Monitor Module [DI-9319E]
    UTC™ GST® Loop Monitor Module
    Ref.: DI-9319E
    Input port cable monitoring with 4.7K? EOLR. Monitoring power supply. Two indicators for fire and fault. Normally-open or Normally-close output automatically follows input port to change state. Electronically addressed. Addresses can be modified in field. LED status indication. Din-Rail mount or surface mount. Standard: EN 54-18:2005. LPCB Approved.
    V.A.T. included
    Consult
    UTC™ GST® Monitor Input Module [DI-9305E]
    UTC™ GST® Monitor Input Module
    Ref.: DI-9305E
    Input port monitored. Output port monitored with 47K? EOLR. Double-contact relay switching 2 lines together. Electronically addressed. Addresses can be modified in field. Output port utilizes AD sampling technology for precise testing. LED status indication. Din-Rail mount, Surface mount. Standard: EN 54-18:2005. LPCB Approved.
    V.A.T. included
    Consult
    UTC™ GST® Addr. Single Output Module [DI-9301E]
    UTC™ GST® Addr. Single Output Module
    Ref.: DI-9301E
    Intelligent addressable input/output module loop powered. A single volt free relay with N/O and N/C change over contacts that can be driven via the fire alarm loop. Commonly used for overriding equipment such as AHU’s, Lift auto dialer, BMS and etc. The input can be linked through a volt free contact switch output of ancillary equipment reporting to the fire alarm controller. According to the pre-inputted cause and effects interface programming, the alarm controller sends out a start command to the equipment required to start. After receiving the command, the module activates its relay to change state. Once the equipment under control has operated a confirmation signal can be sent back to the fire alarm controller. Electronic addressing can be done through Handheld Programming tool (P-9910B), purchased separately.
    V.A.T. included
    Consult
    UTC™ GST® Digital Single Input Module [DI-9300E]
    UTC™ GST® Digital Single Input Module
    Ref.: DI-9300E
    Input port monitored with 4.7K? EOLR. Normally open or normally closed contact acceptable. Electronically addressed. Addresses can be modified in field. Built-in microprocessor and AD sampling technology. Loop Powered. LED status indication. Din-Rail mount or surface mount. Standard: EN 54-18:2005. LPCB Approved.
    V.A.T. included
    Consult
    UTC™ GST® Loop Isolator Module [DC-9503E]
    UTC™ GST® Loop Isolator Module
    Ref.: DC-9503E
    Isolation of short circuit, automatic restore when short circuit is cleared. Din-Rail mount, Surface mount. LED status indication. Standard: EN 54-17:2005. LPCB Approved. Operating Voltage: Loop 24VDC (16VDC - 28VDC). Standby Current? 0.15mA. Action Current? 1.5mA. Capacity: Maximum 128 isolators per loop. Maximun 70 devices between two isolators. Operating Environment: 0? - +49?; ? 95%, non-condensing. Dimension: 78 x 45.3 x 28.5 mm.
    V.A.T. included
    Consult
    AC Control Relay Module for UTC™ GST® Power Switching [C-9302]
    AC Control Relay Module for UTC™ GST® Power Switching
    Ref.: C-9302
    The C-9302 interposing relay module is used for interposing ordinary fire alarm devices with heavy duty (high voltage or heavy current) application, to prevent from interference and damage. It’s a non-addressable module, controlled by 24VDC.
    V.A.T. included
    Consult
    LCD Screen for UTC™ GST® IFP8 [SC-800]
    LCD Screen for UTC™ GST® IFP8
    Ref.: SC-800
    LCD Screen for IFP8
    V.A.T. included
    Consult
    CAN Network Card for UTC™ GST® GST-IFP8 (Class-B) [P-9965]
    CAN Network Card for UTC™ GST® GST-IFP8 (Class-B)
    Ref.: P-9965
    P-9965 is an optional card for GST-IFP8 series control panels, providing one photoelectric isolation CAN interface for bus topology and star topology networks. P-9965 CAN Network Card should be fixed in the slot of Loop Board on the motherboard. These cards form ring network through twisted pair.
    V.A.T. included
    Consult
    CAN Network Card for UTC™ GST® GST200-2 (Class A) [P-9960A]
    CAN Network Card for UTC™ GST® GST200-2 (Class A)
    Ref.: P-9960A
    P-9960A is an optional card for GST200 series control panels, providing two photoelectric isolation CAN interfaces. Suitable for ring network. P-9960A CAN Network Card should be fixed in the cabinet using screws. These cards form ring network through twisted pair.
    V.A.T. included
    Consult
    CAN Network Card for UTC™ GST® GST200-2 (Class B) [P-9960]
    CAN Network Card for UTC™ GST® GST200-2 (Class B)
    Ref.: P-9960
    P-9960 network card provides CAN network connection to GST200 series panels. All panels are connected in same line. With CAN Hub, the network can be connected in star topology. Compatible Panel: GST200 series panels Communication Protocol: CAN. Node capacity: 112. Baud Rate: 10,000. Cable Requirement: Minimum 1.0 mm2 Fire Cable Communication Distance: 3000 meters.
    V.A.T. included
    Consult
    RS485 Repeater Network Card for IFP8 Connection to UTC™ GST® GST852RP & RPX [P-9945RP]
    RS485 Repeater Network Card for IFP8 Connection to UTC™ GST® GST852RP & RPX
    Ref.: P-9945RP
    P-9945RP is an optional card for GST-IFP8 control panel, providing RS485 for system integration of the third party. XS3 and XS4 of P-9945RP Repeater Card can be connected with and XS8, XS1 of GST IFP8. XS4?XS1 of a motherboard?can be connected with Repeater 485. XT14 of the mother board can be connected with repeater panel (including GST852RP, GST8903, GST852RPX).
    V.A.T. included
    Consult
    RS485 Network Card for UTC™ GST® GST-IFP8 & NRP01 Class A [P-9945A]
    RS485 Network Card for UTC™ GST® GST-IFP8 & NRP01 Class A
    Ref.: P-9945A
    P-9945A is an optional card for GST-IFP8 control panel, providing two photoelectric isolation RS485 interfaces for ring network. P-9945A Loop Network Card should be fixed in the slot of Loop Board on the motherboard. These cards form ring network through twisted pair.
    V.A.T. included
    Consult
    UTC™ GST® RS485 Class A Network Card [P-9940A]
    UTC™ GST® RS485 Class A Network Card
    Ref.: P-9940A
    RS485 Network Card for GST200 Series, max 1500m, CLASS A. Powered by GST200-2 main board. Communication: 20 pin Ribbon cable connect to GST200-2 main board XS2 port. Networking interface with all GST intelligent FACP RS485 Class A network.
    V.A.T. included
    Consult
    TCP/IP Communications Card for UTC™ GST® GST-IFP8 [P-9935TCP/IP]
    TCP/IP Communications Card for UTC™ GST® GST-IFP8
    Ref.: P-9935TCP/IP
    The TCP / IP communication card P-9935 is an optional card for the GST-IFP8 control panel, which provides a standard IP interface for third-party system integration. This card should not be inserted or removed when activated. Complies with the Ethernet communication protocol.
    V.A.T. included
    Consult
    MODBUS Communications Card for UTC™ GST® GST-IFP8 [P-9935MODBUS]
    MODBUS Communications Card for UTC™ GST® GST-IFP8
    Ref.: P-9935MODBUS
    P-9935 Modbus Communication Card is an optional card for GST-IFP8 control panel, providing standard RS232 interface for system integration of the third party. This card shouldn’t be inserted and removed when it is energized. Complying with Modbus RTU communication protocol. Standard RS232 interface, used for system integration of the third party.
    V.A.T. included
    Consult
    SYSAWAY© 2025 All rights reserved