English
Español
  • Search
    • +34 902930427

    0.00 €

    Products 802
    PULSAR® DC/DC 2Amp (12VDC) Power Converter [DC/DC20SE]
    PULSAR® DC/DC 2Amp (12VDC) Power Converter
    Ref.: DC/DC20SE
    The DC/DC 2Amp (DC/DC20SE) voltage-step up / step down converter is used for maintaining a constant output voltage in the range between 5÷15VDC, adjusted with the VADJ potentiometer, regardless of the input voltage fluctuations in the range of 9.5V ÷ 16VDC. When the input voltage at the output is lower than needed, the converter increases it to the set value. When the input voltage at the output is higher than needed, the converter lowers it to the needed value set by the VADJ potentiometer. The maximum load current is Imax=2Amp (Pmax = 24W). Input voltage: 9.5V÷16VDC. Voltage adjustment range: 5÷15VDC. Output current: 2Amp / 12VDC. Protections: Overload protection, Short-circuit protection. Technical outputs: PSU – converter failure. Dimensions: L=110 W=43 H=27 mm. Installation: a mounting panel with an adhesive tape, mounting screws.
    V.A.T. included
    Consult
    PULSAR® DC/DC 2Amp (12VDC) Power Converter/Reducer [DC/DC20SD]
    PULSAR® DC/DC 2Amp (12VDC) Power Converter/Reducer
    Ref.: DC/DC20SD
    The step down converter DC/DC 2Amp (DC/DC20SD) is used for step down the input voltage from the range between 8V÷28VDC to the voltage range of 4.5V÷19VDC at the output, adjusted with a potentiometer. The maximum load current is Imax=2Amp (Pmax=24W). Input voltage: 8V÷28VDC. Voltage adjustment range: 4.5÷19VDC. Output current: 2Amp / 12VDC. Protections: Short-circuit protection, Overload protection, overheating protection. Technical outputs: PSU – converter failure. Dimensions: L=100 W=43 H=27 mm. Installation: a mounting panel with an adhesive tape, mounting screws. Notes: The minimum difference between the input voltage and the output voltage is: 3V.
    V.A.T. included
    Consult
    PULSAR® DC/DC 52V/1.15A Power Converter for Voltage Increase [DC/DC52115]
    PULSAR® DC/DC 52V/1.15A Power Converter for Voltage Increase
    Ref.: DC/DC52115
    "The DC/DC 52V/1.15A booster module (DC / DC52115) is used to maintain a constant output voltage of 9.5-28 V DC at the 52 V DC voltage at the converter output. The maximum load current is Imax = 1.15 A (Pmax = 60 W). The module does not have galvanic isolation between the input / output (IN-AUX), it operates on the common ""ground"" potential (0V) (the IN- and AUX- terminals are galvanically connected = common terminal)."
    V.A.T. included
    Consult
    PULSAR® DC/DC 52V/2.3A Power Converter for Voltage Increase [DC/DC52230]
    PULSAR® DC/DC 52V/2.3A Power Converter for Voltage Increase
    Ref.: DC/DC52230
    "The DC/DC 52V/2.3A booster module (DC/DC52230) is used to maintain a constant output voltage of 18÷28VDC at the 52 V DC voltage at the converter output. The maximum load current is Imax = 2.3 A (Pmax = 120 W). The module does not have galvanic isolation between the input / output (IN-AUX), it operates on the common ""ground"" potential (0V) (the IN- and AUX- terminals are galvanically connected = common terminal)."
    V.A.T. included
    Consult
    PULSAR® DC/DC 5Amp (12VDC) Power Converter with Isolated I/O [DC/DC50SE-SEP]
    PULSAR® DC/DC 5Amp (12VDC) Power Converter with Isolated I/O
    Ref.: DC/DC50SE-SEP
    The DC/DC 5Amp (DC/DC50SE-SEP) voltage-step up / step down converter is used for maintaining a constant output voltage in the range between 5÷15VDC, adjusted with the VADJ potentiometer, regardless of the input voltage fluctuations in the range of 9.5V ÷ 16VDC. When the input voltage at the output is lower than needed, the converter increases it to the set value. When the input voltage at the output is higher than needed, the converter lowers it to the needed value set by the VADJ potentiometer. The maximum load current is Imax=5Amp (Pmax = 60W). Input voltage: 9.5V÷16VDC. Output voltage: 12VDC / Galvanic isolation: input - output. Output current: 5Amp / 12VDC. Protections: Overload protection, Short-circuit protection. Technical outputs: PSU – converter failure. Dimensions: L=150 W=50 H=60 mm. Installation: a mounting panel with an adhesive tape, mounting screws.
    V.A.T. included
    Consult
    PULSAR® DC/DC 5Amp (12VDC) Power Converter [DC/DC50SE]
    PULSAR® DC/DC 5Amp (12VDC) Power Converter
    Ref.: DC/DC50SE
    The DC/DC 5Amp (DC/DC50SE) voltage-step up / step down converter is used for maintaining a constant output voltage in the range between 5÷15VDC, adjusted with the VADJ potentiometer, regardless of the input voltage fluctuations in the range of 9.5V ÷ 16VDC. When the input voltage at the output is lower than needed, the converter increases it to the set value. When the input voltage at the output is higher than needed, the converter lowers it to the needed value set by the VADJ potentiometer. The maximum load current is Imax=5Amp (Pmax = 60W). Input voltage: 9.5V÷16VDC. Voltage adjustment range: 5÷15VDC. Output current: 5Amp / 12VDC. Protections: Overload protection, Short-circuit protection. Technical outputs: PSU – converter failure. Dimensions: L=150 W=50 H=60 mm. Installation: a mounting panel with an adhesive tape, mounting screws.
    V.A.T. included
    Consult
    PULSAR® DC/DC 5Amp (12VDC) Power Converter/Reducer with Isolated I/O [DC/DC50SD-SEP]
    PULSAR® DC/DC 5Amp (12VDC) Power Converter/Reducer with Isolated I/O
    Ref.: DC/DC50SD-SEP
    The DC/DC 5Amp (DC/DC50SD-SEP) buck converter is used to reduce the voltage from 20V ÷ 28V DC at the converter input to 12VDC at the output. The maximum load current is Imax=5Amp (PMAX= 60W). The module is galvanically isolated between the input and output (IN-AUX). Input voltage: 20V÷28VDC. Output voltage: 12VDC / Galvanic isolation: input - output. Output current: 5Amp/12VDC. Protections: OLP, SCP, OVP. Dimensions: L=150 W=54 H=60 [+/- 2mm]. Installation: a mounting panel with an adhesive tape, mounting screws.
    V.A.T. included
    Consult
    PULSAR® DC/DC 5Amp (12VDC) Power Converter/Reducer [DC/DC50SD]
    PULSAR® DC/DC 5Amp (12VDC) Power Converter/Reducer
    Ref.: DC/DC50SD
    The step down converter DC/DC 5Amp (DC/DC50SD) is used for step down the input voltage from the range between 8V÷28VDC to the voltage range of 4.5V÷24VDC at the output, adjusted with a potentiometer. The maximum load current is Imax=5Amp (Pmax=60W). Input voltage: 8V÷28VDC. Voltage adjustment range: 4.5÷24VDC. Output current: 5Amp / 12VDC. Protections: Short-circuit protection, Overload protection, overheating protection. Technical outputs: PSU – converter failure. Dimensions: L=140 W=43 H=45 mm. Installation: a mounting panel with an adhesive tape, mounting screws. Notes: The minimum difference between the input voltage and the output voltage is: 3V.
    V.A.T. included
    Consult
    PULSAR® DC/DC 5Amp (12VDC) Voltage Reducer [RN500]
    PULSAR® DC/DC 5Amp (12VDC) Voltage Reducer
    Ref.: RN500
    The RN 12V/5Amp (RN500) is intended for lowering and stabilising DC voltage within the range of 9÷14V into the value of 12V. In the case when the output voltage drops below the preset output value, the transistor opens and the reducer conducts without any loss. That enables full use of energy accumulated in the PSU's battery during batter-assisted operation. Voltage: 9V÷14VDC. Output current: 5Amp/24VDC. Protections: Overload protection, Short-circuit protection. Dimensions: L=63, W=67, H=42 [+/- 2mm].
    V.A.T. included
    Consult
    PULSAR® DIN Holder for Power Supplies and Transformers [DIN2]
    PULSAR® DIN Holder for Power Supplies and Transformers
    Ref.: DIN2
    DIN holder for power supplies and transformers. Destination: PS-12V2A, PS-12V3A, PS-12V5A, PS-48V1A, PSB-12V2A, PSB-12V3A, PSB-12V5A, PSB-24V2A, RS-15xxx, RS-25xxx, RS-50xxx, RS-75xxx, LRS-35xxx, LRS-50xxx, LRS-75xxx, TOR/TRP/TRZ 50VA-150VA. Dimensions: 128 x 137 x 25 [+/-2 mm]. MAterial: electrolytic galvanized steel sheet DC01, 1mm, metallic.
    V.A.T. included
    Consult
    PULSAR® DIN Holder for Power Supplies [DIN3]
    PULSAR® DIN Holder for Power Supplies
    Ref.: DIN3
    DIN holder for power supplies. Destination: PS-12V7A, PS-12V10A, PS-12V15A; PS-48V3A, PSB-12V7A, PSB-12V10A, PSB-12V15A, PSB-24V3A, PSB-24V5A, PSB-24V7A, PSB-48V3A, PSG2-12V5A; PSG2-12V7A; PSG2-24V2A; PSG2-24V3A, RS-75xxx, RS-100xxx, RS-150xxx, LRS-75xxx, LRS-100xxx, LRS-150xxx. Dimensions: 142 x 200 x 25 [+/-2 mm]. Material: electrolytic galvanized steel sheet DC01, 1mm, metallic.
    V.A.T. included
    Consult
    PULSAR® DIN Holder for Power Supplies [DIN4]
    PULSAR® DIN Holder for Power Supplies
    Ref.: DIN4
    DIN holder for power supplies. Destination: PSB-12V15A, PSB-12V20A, PSB-24V7A, PSB-24V10A, PSB-48V5A, PSG2-12V10A, PSG2-12V20A, PSG2-24V5A, PSG2-24V10A, PSDC-12V4x1A, PSDC-12V8x1A, PSDC-12V16x1A. Dimensions: 267 x 100 x 25 [+/-2 mm]. Material: electrolytic galvanized steel sheet DC01, 1mm, metallic.
    V.A.T. included
    Consult
    PULSAR® DIN Rail Anchor Kit [ PKAZ107]
    PULSAR® DIN Rail Anchor Kit
    Ref.: PKAZ107
    Mounting kit for DIN rail.
    V.A.T. included
    Consult
    PULSAR® DINB 13,8V/2Amp Buffer PSU for DIN Rail [DINB13820]
    PULSAR® DINB 13,8V/2Amp Buffer PSU for DIN Rail
    Ref.: DINB13820
    The buffer power supply is designed for uninterrupted supply of devices requiring stabilized voltage of 12V DC (+/-15%). The PSU supplies voltage of 13,8V DC with current efficiency of I = 2A + 0,5A battery charging. In the case of mains power failure, the unit will instantly switch to battery power. The PSU is fitted with short circuit protection and overload protection. The power supply unit is in plastic enclosure designed for DIN TH35 rail mounting (35mm width). Power supply: 90÷264VAC. Power supply output: 2A/13,8VDC. Battery charging current: 0,5Amp. Efficiency: 85%. Protections: SCP, OLP, UVP. Dimensions: L=122, W=93, H=50 [+/- 2mm]. Notes: for mounting on a DIN rail.
    V.A.T. included
    Consult
    PULSAR® DINB 13,8V/3Amp Buffer PSU for DIN Rail [DINB13830]
    PULSAR® DINB 13,8V/3Amp Buffer PSU for DIN Rail
    Ref.: DINB13830
    The buffer power supply is designed for uninterrupted supply of devices requiring stabilized voltage of 12V DC (+/-15%). The PSU supplies voltage of 13,8V DC with current efficiency of I = 3A + 0,5A battery charging. In the case of mains power failure, the unit will instantly switch to battery power. The PSU is fitted with short circuit protection and overload protection. The power supply unit is in plastic enclosure designed for DIN TH35 rail mounting (35mm width). Power supply: 90÷264VAC. Power supply output: 3A/13,8VDC. Battery charging current: 0,5Amp. Efficiency: 85%. Protections: SCP, OLP, UVP. Dimensions: L=122, W=93, H=50 [+/- 2mm]. Notes: for mounting on a DIN rail.
    V.A.T. included
    Consult
    PULSAR® DINB 13,8V/5Amp Buffer PSU for DIN Rail [DINB13850]
    PULSAR® DINB 13,8V/5Amp Buffer PSU for DIN Rail
    Ref.: DINB13850
    The buffer power supply is designed for uninterrupted supply of devices requiring stabilized voltage of 12V DC (+/-15%). The PSU supplies voltage of 13,8V DC with current efficiency of I = 5A + 0,5A battery charging. In the case of mains power failure, the unit will instantly switch to battery power. The PSU is fitted with short circuit protection and overload protection. The power supply unit is in plastic enclosure designed for DIN TH35 rail mounting (35mm width). Power supply: 176÷264VAC. Power supply output: 5A/13,8VDC. Battery charging current: 0,5Amp. Efficiency: 85%. Protections: SCP, OLP, UVP. Dimensions: L=122, W=93, H=60 [+/- 2mm]. Notes: for mounting on a DIN rail.
    V.A.T. included
    Consult
    PULSAR® DINB 27,6V/2Amp Buffer PSU for DIN Rail [DINB27620]
    PULSAR® DINB 27,6V/2Amp Buffer PSU for DIN Rail
    Ref.: DINB27620
    The buffer power supply is designed for uninterrupted supply of devices requiring stabilized voltage of 24V DC (+/-15%). The PSU supplies voltage of 27,6V DC with current efficiency of I = 2A + 0,2A battery charging. In the case of mains power failure, the unit will instantly switch to battery power. The PSU is fitted with short circuit protection and overload protection. The power supply unit is in plastic enclosure designed for DIN TH35 rail mounting (35mm width). Power supply: 90÷264VAC. Power supply output: 2A/27,6VDC. Battery charging current: 0,2Amp. Efficiency: 88%. Protections: SCP, OLP, UVP. Dimensions: L=122, W=93, H=50 [+/- 2mm]. Notes: for mounting on a DIN rail.
    V.A.T. included
    Consult
    PULSAR® DINB 27,6V/3Amp Buffer PSU for DIN Rail [DINB27630]
    PULSAR® DINB 27,6V/3Amp Buffer PSU for DIN Rail
    Ref.: DINB27630
    The buffer power supply is designed for uninterrupted supply of devices requiring stabilized voltage of 24V DC (+/-15%). The PSU supplies voltage of 27.6V DC with current efficiency of I = 3A + 0.2A battery charging. In the case of mains power failure, the unit will instantly switch to battery power. The PSU is fitted with short circuit protection and overload protection. The power supply unit is in plastic enclosure designed for DIN TH35 rail mounting (35mm width). Power supply: 176÷264VAC. Power supply output: 3A/27,6VDC. Battery charging current: 0,2Amp. Efficiency: 88%. Protections: SCP, OLP, UVP. Dimensions: L=122, W=93, H=60 [+/- 2mm]. Notes: for mounting on a DIN rail.
    V.A.T. included
    Consult
    PULSAR® Enclosure for Loudspeaker Line [AWO506]
    PULSAR® Enclosure for Loudspeaker Line
    Ref.: AWO506
    Application: The enclosure is designed for mounting loudspeaker line supervision systems by Bosch used in Voice Alarm Systems. Dimensions: W=154 H=113 D=38 mm. Installation cable diameter: max 10mm. Cable cross section: max. 2,5mm2. Finish: DC01 sheet, thickness: 1,0mm, corrosion protection, color: RAL 9003 (white). Notes: surface mounted enclosure, closing – screwed.
    V.A.T. included
    Consult
    PULSAR® ETHERNET Interface [INTE-C]
    PULSAR® ETHERNET Interface
    Ref.: INTE-C
    Intended use: The ETHERNET interface is a device intended for connecting the power supplies of the EN54C-LCD series with a PC in the Ethernet network. The PowerSecurity system enables a remote monitoring of the parameters through a cyclical preview of the current status of the PSU, reading of the event history, preview of current and voltage charts and a remote battery test. Power supply: 5V DC(max. 0,95W) from the serial outlet of the PSU. TTL transmission’s speed: 115200 bauds, with parity check. LAN transmission’s speed: 10/100Mbps (auto-negotation). Dimensions: 63 x 50 x 24 [mm]. Works with the PowerSecurity programming software. Embedded web server for configuration.
    V.A.T. included
    Consult
    PULSAR® ETHERNET Interface [INTE]
    PULSAR® ETHERNET Interface
    Ref.: INTE
    Intended use: The ETHERNET interface is a device intended for connecting the power supplies of the PSBEN (Black Power) / EN54 (Red Power) series with a PC in the Ethernet network. The PowerSecurity system enables a remote monitoring of the parameters through a cyclical preview of the current status of the PSU, reading of the event history, preview of current and voltage charts and a remote battery test. Power supply: 5V DC(max. 0,95W) from the serial outlet of the PSU. TTL transmission’s speed: 115200 bauds, with parity check. LAN transmission’s speed: 10/100Mbps (auto-negotation). Dimensions: 63 x 50 x 24 [mm]. Works with the PowerSecurity programming software. Embedded web server for configuration.
    V.A.T. included
    Consult
    PULSAR® Fan with Temperature Sensor (45°C) [ARAW45]
    PULSAR® Fan with Temperature Sensor (45°C)
    Ref.: ARAW45
    The fan with a temperature sensor is intended to be mounted in RACK enclosures, type: ARAD2 / ARAD3 / ARAD4. After exceeding 45°C, it triggers airflow inside the enclosure. Power Supply: 220 ÷ 230V AC, 50Hz. Current consumption: 0.08Amp. Power consumption: 16W. Rotational speed (RPM): 2300 rev / min. Air flow: 21CMF / 0,59 m3/min. Short-circuit protection: T 200mA. Fan start temperature: 45°C. Fan’s dimensions: 78 x 78 x 25 mm.
    V.A.T. included
    Consult
    PULSAR® HDMI-VGA Signal Converter [HDMI-VGA]
    PULSAR® HDMI-VGA Signal Converter
    Ref.: HDMI-VGA
    The HDMI-VGA signal converter allows connecting devices (DVRs/NVRs) equipped with HDMI sockets to monitors using only a VGA (D-Sub) input. Video input: 1 x HDMI (HDMI 1.3, HDCP 1.4). Video output / supported resolutions: 1 x VGA / 640x480 ÷ 1920x1080 (details can be found in the data sheet). Audio output: 1 x 3.5mm JACK. Power input: 1 x USB (mini). Dimensions: W=66, H=55, D=20mm.
    V.A.T. included
    Consult
    PULSAR® High Voltage DC/DC 3Amp (12VDC) Power Reducer [DC/DC30HV]
    PULSAR® High Voltage DC/DC 3Amp (12VDC) Power Reducer
    Ref.: DC/DC30HV
    The step down converter DC/DC 3Amp (DC/DC30HV) is used for step down the input voltage from the range between 28V÷60VDC to the voltage range of 12V÷24VDC at the output, adjusted with a potentiometer. The maximum load current is Imax=3Amp (Pmax=36W). Input voltage: 28V÷60VDC. Voltage adjustment range: 12÷24VDC. Output current: 3Amp/12VDC. Protections: OLP, SCP. Technical outputs: PSU – converter failure. Dimensions: L=130 W=43 H=45 mm. Installation: a mounting panel with an adhesive tape, mounting screws.
    V.A.T. included
    Consult
    SYSAWAY© 2025 All rights reserved