English
Español
  • Search
    • +34 902930427

    0.00 €

    Products 432
    Long Range CDVI® PASS™ Antenna AN01RCP with Built-in Receiver [F0103000139]
    Long Range CDVI® PASS™ Antenna AN01RCP with Built-in Receiver
    Ref.: F0103000139
    The trigger antenna AN01RCP transmits periodically a trigger signal (with a period of 0,5 - 2,4 Sec) at 125 KHz, with a predefined pattern, that awakes the active cards standing in the detection zone [6 - 15 m]. Once awakened, the card, at its turn, sends a signal at 433,92 MHz to the built-in receiver of the antenna. The receiver can activate directly a relay or send out on the bus wiegand the s/n of the tag, that can be managed by a further access control system. The memory of the built-in receiver can hold up to 500 cards. A 10-position rotary switch allows to identify each antenna with a unique number, included in the wiegand protocol (26, 30 or 44 bits). Each antenna can even be enabled by an external PIR (not provided).
    V.A.T. included
    701.80 €
    Low Range CDVI® PASS ™ Antenna AN02CP [F0103000123]
    Low Range CDVI® PASS ™ Antenna AN02CP
    Ref.: F0103000123
    The 125KHz antenna is part of the CDVI® PASS system. It transmits periodically a trigger signal (with a period of 0,5 - 2,4 Sec) with a predefined pattern to awake the active cards. Each single transmission lasts 34ms. External inputs allow synchronization with other antennas (up to 4). When sync-in and sync-out are left open, the gap between two transmissions is 2.4 Sec. When shorted, it is reduced to 500mS. The enable input handles the transmission. Before each transmission, the system controls this input and if it is left open, the transmission is inhibited. Using the onboard rotary trimmer, it is possible to assign an ID (0-9) to the antenna to distinguish it from the other. Additionally, inputs for two PIR sensors are provided ( internal and external one) to awake the antenna only in presence of movement.
    V.A.T. included
    321.86 €
    Low Range CDVI® PASS ™ Antenna AN02RCP with Built-in Receiver [F0103000138]
    Low Range CDVI® PASS ™ Antenna AN02RCP with Built-in Receiver
    Ref.: F0103000138
    The trigger antenna AN02RCP transmits periodically a trigger signal (with a period of 0,5 - 2,4 Sec) at 125 KHz, with a predefined pattern, that awakes the active cards standing in the detection zone [0,3 - 6 m]. Once awakened, the card, at its turn, sends a signal at 433,92 MHz to the built-in receiver of the antenna. The receiver can activate directly a relay or send out on the bus wiegand the s/n of the tag, that can be managed by a further access control system. The memory of the built-in receiver can hold up to 500 cards. A 10-position rotary switch allows to identify each antenna with a unique number, included in the wiegand protocol ( 26,30 or 44 bits ). Each antenna can even be enabled by an external PIR ( not provided ).
    V.A.T. included
    415.03 €
    LPR License for CDVI® ATRIUM™ (ACPR) [F0115000027]
    LPR License for CDVI® ATRIUM™ (ACPR)
    Ref.: F0115000027
    ACPR (ATRIUM Car Plate Recognition) works with any smart numberplate recognition camera with a 26-bit Wiegand output. Users registered in the ATRIUM access control system have numberplates assigned to them. When drivers approach a gate or barrier, their numberplate is scanned and checked in the ATRIUM database. If the numberplate is registered to an authorised user, the gate or barrier opens to allow access. ACPR creates a seamless single security environment, with physical access control and parking facilities controlled by the same database. This makes management easier, relieves administrative burdens, and reduces the risk of human error.
    V.A.T. included
    227.48 €
    Metal Control Unit Enclosure (IP20) [ACU-BOX]
    Metal Control Unit Enclosure (IP20)
    Ref.: ACU-BOX
    Metal enclosure for connection wires and HID® VertX™, EDGE™, AXIS®, CDVI® and ACP® inBIO™ access control units. Class: IP20. It allows up to 2 controllers, 1 power source and 1 12VDC 7Ah battery. Wall/Surface mount.
    V.A.T. included
    163.35 €
    OTS™ 140 Hydraulic Closer [K-17042-00-0-1]
    OTS™ 140 Hydraulic Closer
    Ref.: K-17042-00-0-1
    OTS™ 140 is universally usable for wooden, PVC, aluminum and steel swing doors. With pinion and articulated arm, according to UNE-EN 1154. SILVER Color. Usable for left or right in normal mounting or on the frame (normal mounting of the body on the blade, external mounting on the frame). 180º opening and closing angle, provided the construction conditions allow. Completely controlled closing from each opening angle. Safety valve on the closer that protects the overload. Hydraulic damping of the closing movement by means of closing speed adjustable progressively. The adjustment of the final blow of the door is made through a second control valve. With retention arm. Adjustable retention zone between approximately 70 ° and 150 ° of door opening.
    V.A.T. included
    Consult
    OTS™ 140 Hydraulic Closer [K-17042-00-0-6]
    OTS™ 140 Hydraulic Closer
    Ref.: K-17042-00-0-6
    OTS™ 140 is universally usable for wooden, PVC, aluminum and steel swing doors. With pinion and articulated arm, according to UNE-EN 1154. BLACK Color. Usable for left or right in normal mounting or on the frame (normal mounting of the body on the blade, external mounting on the frame). 180º opening and closing angle, provided the construction conditions allow. Completely controlled closing from each opening angle. Safety valve on the closer that protects the overload. Hydraulic damping of the closing movement by means of closing speed adjustable progressively. The adjustment of the final blow of the door is made through a second control valve. With retention arm. Adjustable retention zone between approximately 70 ° and 150 ° of door opening.
    V.A.T. included
    Consult
    OTS™ 140 Hydraulic Closer [K-17042-00-0-7]
    OTS™ 140 Hydraulic Closer
    Ref.: K-17042-00-0-7
    OTS™ 140 is universally usable for wooden, PVC, aluminum and steel swing doors. With pinion and articulated arm, according to UNE-EN 1154. WHITE Color (RAL 9016). Usable for left or right in normal mounting or on the frame (normal mounting of the body on the blade, external mounting on the frame). 180º opening and closing angle, provided the construction conditions allow. Completely controlled closing from each opening angle. Safety valve on the closer that protects the overload. Hydraulic damping of the closing movement by means of closing speed adjustable progressively. The adjustment of the final blow of the door is made through a second control valve. With retention arm. Adjustable retention zone between approximately 70 ° and 150 ° of door opening.
    V.A.T. included
    Consult
    OTS™ 536 Hydraulic Closer [K-17920-00-0-1]
    OTS™ 536 Hydraulic Closer
    Ref.: K-17920-00-0-1
    OTS ™ 536 allows trouble-free fastening to wood, plastic, aluminum or steel doors by the mounting plate with different groups of holes. With pinion and articulated arm, according to UNE-EN 1154. SILVER Color. Width of door leaf up to 1400 mm. Usable on left or right. Normal mounting and on frame. 180º door opening angle, provided that the construction conditions allow. Closure controlled from each opening angle. Safety valves in the closer protect the overload in the closing and opening direction. Shaft with needle roller. If the OTS ™ 536 is used for fire and smoke doors, you must observe UNE-EN 1154, closers with controlled closing process.
    V.A.T. included
    Consult
    OTS™ 536 Hydraulic Closer [K-17920-00-0-6]
    OTS™ 536 Hydraulic Closer
    Ref.: K-17920-00-0-6
    OTS ™ 536 allows trouble-free fastening to wood, plastic, aluminum or steel doors by the mounting plate with different groups of holes. With pinion and articulated arm, according to UNE-EN 1154. BLACK Color. Width of door leaf up to 1400 mm. Usable on left or right. Normal mounting and on frame. 180º door opening angle, provided that the construction conditions allow. Closure controlled from each opening angle. Safety valves in the closer protect the overload in the closing and opening direction. Shaft with needle roller. If the OTS ™ 536 is used for fire and smoke doors, you must observe UNE-EN 1154, closers with controlled closing process.
    V.A.T. included
    Consult
    OTS™ 536 Hydraulic Closer [K-17920-00-0-7]
    OTS™ 536 Hydraulic Closer
    Ref.: K-17920-00-0-7
    OTS ™ 536 allows trouble-free fastening to wood, plastic, aluminum or steel doors by the mounting plate with different groups of holes. With pinion and articulated arm, according to UNE-EN 1154. WHITE Color. Width of door leaf up to 1400 mm. Usable on left or right. Normal mounting and on frame. 180º door opening angle, provided that the construction conditions allow. Closure controlled from each opening angle. Safety valves in the closer protect the overload in the closing and opening direction. Shaft with needle roller. If the OTS ™ 536 is used for fire and smoke doors, you must observe UNE-EN 1154, closers with controlled closing process.
    V.A.T. included
    Consult
    OTS™ 536 Retention Arm for Closer [K-17923-00-0-1]
    OTS™ 536 Retention Arm for Closer
    Ref.: K-17923-00-0-1
    Retention arm for OTS ™ 536 (connectable and detachable). Not allowed for fire doors and smoke locks (RF). SILVER color.
    V.A.T. included
    Consult
    OTS™ 536 Retention Arm for Closer [K-17923-00-0-6]
    OTS™ 536 Retention Arm for Closer
    Ref.: K-17923-00-0-6
    Retention arm for OTS ™ 536 (connectable and detachable). Not allowed for fire doors and smoke locks (RF). BLACK color.
    V.A.T. included
    Consult
    OTS™ 536 Retention Arm for Closer [K-17923-00-0-7]
    OTS™ 536 Retention Arm for Closer
    Ref.: K-17923-00-0-7
    Retention arm for OTS ™ 536 (connectable and detachable). Not allowed for fire doors and smoke locks (RF). WHITE color (RAL 9016).
    V.A.T. included
    Consult
    OTS™ 634 Hydraulic Closers [K-17523-00-0-1]
    OTS™ 634 Hydraulic Closers
    Ref.: K-17523-00-0-1
    OTS ™ 634 allows normal door mounting; mounting on the outer frame is only possible using a block to limit the opening of the door. Usable on left or right. For doors up to 1100 mm wide. Seamlessly fastened to wooden, PVC, aluminum or steel doors. 180° opening and closing angle. Completely controlled closing from each opening angle. Safety valve on the door closer protects the overload. SILVER color.
    V.A.T. included
    Consult
    OTS™ 634 Hydraulic Closers [K-17523-00-0-6]
    OTS™ 634 Hydraulic Closers
    Ref.: K-17523-00-0-6
    OTS ™ 634 allows normal door mounting; mounting on the outer frame is only possible using a block to limit the opening of the door. Usable on left or right. For doors up to 1100 mm wide. Seamlessly fastened to wooden, PVC, aluminum or steel doors. 180° opening and closing angle. Completely controlled closing from each opening angle. Safety valve on the door closer protects the overload. BLACK color.
    V.A.T. included
    Consult
    OTS™ 634 Hydraulic Closers [K-17523-00-0-7]
    OTS™ 634 Hydraulic Closers
    Ref.: K-17523-00-0-7
    OTS ™ 634 allows normal door mounting; mounting on the outer frame is only possible using a block to limit the opening of the door. Usable on left or right. For doors up to 1100 mm wide. Seamlessly fastened to wooden, PVC, aluminum or steel doors. 180° opening and closing angle. Completely controlled closing from each opening angle. Safety valve on the door closer protects the overload. WHITE color (RAL 9016).
    V.A.T. included
    Consult
    OTS™ 634 Retention Mechanism for Closers [K-17726-00-0-0]
    OTS™ 634 Retention Mechanism for Closers
    Ref.: K-17726-00-0-0
    Retention mechanism for OTS™ 634. Not allowed for fire doors and smoke protection.
    V.A.T. included
    Consult
    Protective Case for CDVI® FTC1000 Scanner [CU001]
    Protective Case for CDVI® FTC1000 Scanner
    Ref.: CU001
    This housing includes a thermostat that, when 12 ° is reached, activates a heater until the internal temperature reaches 18 °. The enclosure includes the following: 1 fan. 1 heater. 1 thermostat. 1 20A power supply. 1 stainless steel casing.
    V.A.T. included
    Consult
    RXCP Receiver for CDVI® PASS ™ [F0103000121]
    RXCP Receiver for CDVI® PASS ™
    Ref.: F0103000121
    The receiver RXCP makes part of the system CDVI® Pass: a radio system for the access control of persons and vehicles based on radio active tags. The system is mainly composed by 3 devices: one or more active tag, one trigger antenna and one receiver. It finds application in domestic, pubblic, residential and industrial environment, both for personal and vehicular use. The users or the vehicles carrying the active card and standing in the detection zone of the trigger aerial, are identified waking-up the tag, which is normally in stand-by and decoding the tag information. The serial number of the tag, that identifies uniquely the user, is then transmitted via radio to the receiver, which, at its turn, sends the information to any access control system, through a bus RS-485 or wiegand line.
    V.A.T. included
    168.19 €
    UHF CDVI® ATU48 Adhesive Card (Pack of 10 Units) [F0103000129]
    UHF CDVI® ATU48 Adhesive Card (Pack of 10 Units)
    Ref.: F0103000129
    Adhesive to adhere to the front windshield, on its surface. Frequency 860 ~ 960MHz FCC (US): 902 MHz ~ 928 MHz - ETSI (EU): 865.6 MHz ~ 867.5MHz, 896.85 MHz. Material: PVC, PET. Read / write cycles:> 100,000 cycles. Reading distance: 3 ÷ 10 m (in stable conditions and in relation to the reader used).
    V.A.T. included
    57.17 €
    UHF CDVI® CTU48 Card (Pack of 10 Units) [F0103000132]
    UHF CDVI® CTU48 Card (Pack of 10 Units)
    Ref.: F0103000132
    Frequency 860 ~ 960MHz FCC (US): 902 MHz ~ 928 MHz - ETSI (EU): 865.6 MHz ~ 867.5MHz, 896.85 MHz. Material: PVC, PET. Read / write cycles:> 100,000 cycles. Data maintenance: 10 years. Protocols: ISO18000-6B, ISO18000-6C / EPC GEN2. Reading distance: 3 ÷ 10 m (in stable conditions and in relation to the reader used). Memory: 512 bits Microprocessor: Alien Higgs-3. Dimensions: 85.6 x 54 x 0.8 mm. Operating temperature: -20 ° C ÷ + 70 ° C. Storage temperature: -20 ° C ÷ + 70 °. C
    V.A.T. included
    57.17 €
    UHF CDVI® PTU48 Tag [F0103000134]
    UHF CDVI® PTU48 Tag
    Ref.: F0103000134
    U4GO is a high performance UHF (902-928 MHz) integrated system perfect for vehicle and people identification. The U4GO system provides secure acces for many applications such parking facility, gated community, campus and rolling stock. The U4GO readers are easy to install, versatile, and is perfectly suited for access control systems (Wiegand output). The high security protocol (AES128) RF module can also manage up to 100 remote controls. RFID tag designed for vehicle access. Dust and water resistant. Operates in harsh environment. Compatible with A6U49 or A10U49.
    V.A.T. included
    Consult
    Ventosa Electromagnética CDVI® PWM25PSRSP de Cizalla [F0535000028]
    Ventosa Electromagnética CDVI® PWM25PSRSP de Cizalla
    Ref.: F0535000028
    Self-Aligning electromagnetic shearlocks, mortice mount, for narrow profiles (25 mm), monitored (lock status). Holding force: 800 Kgs. With built-in varistor (Electronic protection to eliminate back EMF). Indoor installation. 12/24 VDC. With illuminated output button. RAL option to be choosen.
    V.A.T. included
    959.53 €
    SYSAWAY© 2024 All rights reserved