The power adapter allows you to connect a PSU equipped with 2.1/5.5 socket to the HIKVISION DVR equipped with four pin power supply. Operation voltage: 30VDC. Current max.: 5,0A. Plug – socket: JACK 2,1/5,5 (male). Plug – plug: DIN4 (male). Wire Run Length: 10 cm

Internal power supply for TruVision™ NVR 70. Refill.

Universal power supply 12VDC, 5.0 Amps.

Universal power supply 12VDC, 3.5 Amps.

12VDC 1000mA power supply.

Power supply for TruVision PTZ domes, 24VAC, 4 Amps.

Reduction cable-outlet DC 5,5/2,1 - enables easy connection of the receivers that end with a power wire with a plug of DC5,5/2,1 type e.g. PSA, PSD, PSC. 100 pieces in a single package.

CABLE - PLUG DC 5,5/2,1/N reduction - enables easy connection of the receivers that feature a DC5,5/2,1 outlet type to a power circuit e.g. fuse modules of LB4, LB8 series. One-piece connection block. 100 pieces in a single package.

Reduction cable-outlet DC 5,5/2,1/N- enables easy connection of the receivers that end with a power wire with a plug of DC5,5/2,1 type e.g. PSA, PSD, PSC. One-piece connection block. 100 pieces in a single package.

Reduction cable-plug DC 5,5/2,1- enables easy connection of the receivers that feature a DC5,5/2,1 outlet type to a power circuit e.g. fuse modules of LB4, LB8 series. 100 pieces in a single package.

A safety backed power supply module is designed for an uninterrupted supply of alarm system devices that require a stabilized voltage of 12 VDC (+/- 15%). A linear stabilization system, which has been used in the unit, provides voltage with a lower noise level and a faster response to interference compared to a switched mode regulator. The PSU module provides a voltage of U = 13.8 VDC with current capacity: (1) Output current 1Amp (without battery). (2) Output current 0.9Amp + 0.1Amp for battery charge. In the event of a power failure, a backup battery is activated immediately. Power supply: 16V ÷ 17 VAC. Current consumption 1.9Amp. Output voltage 12.8V ÷ 13.8 VDC - backup operation. 14W PSU power. Output voltage adjustment range 12 ÷ 14.5 VDC. Output current: (1) 1Amp without battery. (2) 0.9Amp + 0.1Amp to charge the battery. Linear voltage regulator. Protection types: short circuit, overload, overheating, overvoltage. Dimensions: 90 x 72 x 55 mm. Working temperature: -10° C ... + 40° C. Transformers required: AWT150, AWT070.

Power distribution module for IP cameras (PoE). Size: 150 x 53 x 24 mm, Uin=20÷56 VDC (+/-2%), UPoE=Uin (equal to supply voltage), 4x1.0A. Number of power inputs: 2 - DC 5.5/2.1 socket or screw terminal – max. cable length 2.5mm2. Number of PoE outputs: 4 – RJ45. Technical outputs relay and OC type: FPS - fuse failure or power failure DC. The module supports both 10Mbps and 100Mbps networks.

Stabilized DC power supply is intended for supply LAN devices complied with IEEE 802.3at through Ethernet Cable, which require stabilized voltage of 37÷57V DC. The unit provide power through 4/5pins(+) and 7/8pins(-) in Ethernet Cable that according to the Ethernet standard are also used to transmit data. The Power supply can't be used in Gigabit Ethernet! The unit is protected against overvoltage and overload. Desktop type power supply unit. Size: 119 x 61 x 38 mm. Input: 90÷264VAC. Output: 0.3A/52VDC – RJ45 compliant with IEEE 802.3 af, designed for 10Mbit/s and 100Mbit/s.

Universal power supply 12VDC, 5.0 Amps.

Power supply for TVR11(4/8ch), TVR12(4/8ch), TVR15HD (4/8ch), TVN10 (Non-PoE), TVN11 (Non-PoE). Dimensions: 52.4 x 31.3 x 116.3 mm.

Universal power supply 12VDC, 3.5 Amps.

A buffer PSU module is intended for an uninterrupted supply to devices requiring stabilised voltage of 12VDC (+/-15%). The PSU module provides voltage of 13.8 VDC with current capacity. In case of power failure, a battery back-up is activated immediately. Power supply: 18V÷22VAC/50Hz/with transformers AWT8161820, AWT039, AWT800. Power supply output: 3Amp/13.8VDC. Battery charging current: 0.5Amp/1Amp. Efficiency: 81%. Protections: short-circuit, overload, overheat, over voltage. Technical outputs OC type: EPS – AC network failure, PSU – power supply failure, LoB – low battery voltage. Dimensions: L=88, W=93, H=55 [+/- 2mm].

Power distribution module for IP cameras (PoE). Size: 75 x 73 x 33 mm, Uin=20÷56 VDC (+/-2%), UPoE=Uin (equal to supply voltage), 4x1.0A. Number of power inputs: 2 - DC 5.5/2.1 socket or screw terminal – max. cable length 1.5mm2. Number of PoE outputs: 4 – RJ45. The module supports both 10Mbps and 100Mbps networks.

Stabilized DC power supply is intended for supply any LAN devices through Ethernet Cable, which require stabilized voltage of 48V DC. The unit provide power through 4/5pins(+) and 7/8pins(-) in Ethernet cable that according to the Ethernet standard are not used to transmit data (data communication is made using pairs: 1/2 and 3/6). The Power supply can't be used in Gigabit Ethernet! The unit is protected against short-circuit and overload. Desktop type power supply unit. Size: 119 x 61 x 38 mm. Input: 90÷264VAC. Output: 0.5A/48VDC – RJ45, designed for 10Mbit/s and 100Mbit/s.

PoE buffer power supply unit for IP cameras. Size: 300 x 407 x 126 mm. Uin=176÷264VAC, Uout=54VDC. ?I=4x0.25A + 0.3A battery charging. Tamper: 1xNC, 4x7Ah-UVP, OLP, OVP, SCP with standard fuses or PTC fuses, FPS – (indication of output fuse activation) - OC type and relay type.

Switch mode buffer power supply unit for HD cameras 13,8VDC and recorder 12VDC, and recorder space + transmitters. Size: 425 x 540 x 190+14 mm. ?I=11A, 16x0.8A/13.8VDC + 1x5A/12VDC (RJ45 + JACK5.5/2.1). Set includes P-TRPV120 transmitters for up to 12 cameras (Recorder space: 380 x 335 x 80 mm). Tamper: 1xNC, 17Ah-UVP (battery protection).

Switch mode buffer power supply unit (transformerless) for cameras 12VDC (+/- 15%). Size: 285 x 297 x 80+8 mm. Uin=176÷264VAC, Uout=13,8VDC/5x1A. ?I=5A+2A. Tamper: 1xNC, 17Ah. SCP (short-circuit protection) with standard fuses, OVP (over voltage protection), OLP (overload protection), UVP (deep discharge battery protection).

Power supply for cameras 12VDC with independent control of each output channel. Size: 205 x 220 x 50+8 mm. Uin=85÷264VAC, Uout=12,0÷15VDC. 4 x adjustment. 4x1A (independent regulation and galvanic separation of each channel). OVP (over voltage protection), SCP (short-circuit protection) with standard fuses.

Power supply for 12VDC cameras, for long lines with galvanic separation of each channel dedicated to DCDC-H inverters. Size: 270 x 154 x 80+8 mm. Uout=30V÷35VDC (100% load ÷ 0% load). 4x1A@30V DC max. SCP (short-circuit protection): 4x T 1A with standard fuses. Power supply - intended to the DCDC10H and DCDC15H converters).